MML Commands

Having worked on a BSC before, I can tell you the learning curve is very steep. And getting help can be a daunting task.

In this post, I will share with you the MML commands I had to read through while learning configuration of Nokia Siemens Networks BSC. You can always get much needed specific help from veterans at Telecom Funda Forum

MML COMMAND LIST
ZA	ALARM SYSTEM ADMINISTRATION
ZA	B	BLOCKED ALARMS HANDLING COMMANDS
		B	BLOCK ALARM
		U	UNBLOCK ALARMS
		O	OUTPUT BLOCKED ALARMS
ZA	C	ALARM CANCELLING COMMANDS
		C	CANCEL ACCORDING TO CONSECUTIVE NUMBER
		A	CANCEL ACCORDING TO ALARM NUMBER
ZA	E	ERROR RATIO COUNTER HANDLING COMMANDS
		M	MODIFY ERROR RATIO COUNTER BASE VALUE
		O	OUTPUT ERROR RATIO COUNTER VALUES
ZA	H	ALARM HISTORY HANDLING COMMANDS
		O	PRINT ALARMS CURRENTLY ON
		P	PRINT ALARM HISTORY
ZA	L	LAMP PANEL HANDLING COMMANDS
		D	DISPLAY STATE OF ALARM OUTPUTS
		O	DISPLAY UPDATING OF ALARM OUTPUTS FROM LOCAL SYSTEM
		L	DISPLAY UPDATING OF ALARM OUTPUTS INTO LOCAL SYSTEM
		U	SET UPDATING OF ALARM OUTPUTS
		S	SET STATE OF ALARM OUTPUTS
ZA	O	ALARM OPERATING INSTRUCTION HANDLING COMMANDS
		A	ADD OPERATING INSTRUCTIONS
		C	CHANGE OPERATING INSTRUCTIONS
		D	DELETE OPERATING INSTRUCTIONS
		L	LIST OPERATING INSTRUCTIONS
ZA	P	ALARM PARAMETERS HANDLING COMMANDS
		M	MODIFY ALARM PARAMETERS
		O	OUTPUT ALARM PARAMETERS
ZA	R	ALARM PARAMETERS HANDLING COMMANDS
		A	ADD SUPPORTING/PREVENTING RULE
		D	DELETE SUPPORTING/PREVENTING RULE
		M	MODIFY SUPPORTING RULE
		O	OUTPUT SUPPORTING/PREVENTING RULES
		R	RESTORE SUPPORTING/PREVENTING RULE
ZA	T	ALARM PRINTING HANDLING COMMANDS
		B	BLOCK ALARM CLASS PRINTING
		U	UNBLOCK ALARM CLASS PRINTING
		O	OUTPUT PRINTING STATES
		S	SET ALARM PRINTING TIMES
		D	DISPLAY ALARM PRINTING TIMES
		C	CHANGE ALARM PRINTING PARAMETERS
		L	OUTPUT ALARM PRINTING PARAMETERS
ZC	ROUTING STATE ADMINISTRATION
ZC	E	CIRCUIT STATE HANDLING COMMANDS
		C	CHANGE EXTERNAL CIRCUIT STATE
		P	CLEAR PHONE CALL
		T	CALL CONNECTION INFORMATION
		L	LIST EXTERNAL CIRCUIT STATE
ZC	I	INTERNAL ROUTING STATE COMMANDS
		M	MODIFY INTERNAL CIRCUIT OR CIRCUIT GROUP STATE
		I	INTERROGATE INTERNAL CIRCUIT OR CIRCUIT GROUP STATE
		C	MODIFY INTERNAL ROUTE STATE
		L	INTERROGATE INTERNAL ROUTE STATE
ZC	R	CIRCUIT GROUP AND ROUTE STATE COMMANDS
		M	MODIFY EXTERNAL CIRCUIT GROUP STATE
		I	INTERROGATE EXTERNAL CIRCUIT GROUP STATE
		C	MODIFY EXTERNAL ROUTE STATE
		L	INTERROGATE EXTERNAL ROUTE STATE
ZD	SYSTEM SUPPORT AND COMMUNICATION
ZD	B	DATABASE HANDLING COMMANDS
		F	LIST DATABASE FILES
		B	BUILD DIRECTORY
		E	DISPLAY DATABASE FILL RATIO
		L	LIST DATABASES
		C	COPY DATABASE TO DISK
		P	PREVENT UPDATING OF DATABASE IN MEMORY OR TO DISK
		Q	MAKE QUERIES TO DATABASE
		R	RESUME UPDATING OF DATABASE IN MEMORY OR TO DISK
		S	DISPLAY DATABASE STATE
		T	PREVENT OR RESUME DATABASE REMOTE COPY UPDATING
		M	COPY DATABASE FROM DISK TO UNIT OR REFRESH SUBDATABASE
		O	SAVE DATABASE LOG TO DISK
		X	EMPTY DATABASE DISK UPDATING LOG
		Y	SET DATABASE CONSISTENCY
		D	DISPLAY DISK UPDATING SYSTEM STATE
		W	COPY DATABASE FROM DISK TO DISK
		V	CHECK INTEGRITY
ZD	C	CLOCK HANDLING COMMANDS
		D	DISPLAY DATE, TIME AND TIME ZONE
		C	CHECK DATE AND TIME
		S	SET DATE, TIME AND SUMMER TIME
		A	ADJUST TIME
		T	CHANGE TO STANDARD/SUMMER TIME
		E	SET TIMEZONE
ZD	D	REMOTE DEBUGGER SESSION COMMANDS
		S	START REMOTE SESSION
		E	EXECUTE DEBUGGER COMMAND
		T	START REMOTE PREPROCESSOR SESSION
		X	EXECUTE PREPROCESSOR DEBUGGER COMMAND
ZD	E	FILE CONVERSION HANDLING COMMANDS
		C	CREATE MEMORY FILE ON DISK OR MEMORY
		E	EXECUTE PROGRAM
		M	COPY MEMORY FILE ON DISK OR MEMORY
		S	UPDATE MEMORY FILE CHECKSUMS AND BITMAP ON DISK
		I	INTERROGATE FILE ATTRIBUTES ON DISK
		U	CHECK FILE SYSTEM INTEGRITY ON DISK
		V	COMPARE TWO FILES SYSTEMS ON DISK
		P	DISPLAY FILE DIMENSIONING PARAMETERS
		Y	INTERROGATE/CHANGE ENVIRONMENT SETTINGS
		F	MODIFY MEMORY FILE HEADER ON DISK
		R	DISPLAY REPORT FILE OF CONVERSIONS
		X	DISPLAY PROGRESS OF CONVERSIONS
ZD	F	MEMORY FILE HANDLING COMMANDS
		D	DISPLAY FILE OR RECORDS
		S	SUBSTITUTE RECORDS OR SUBRECORDS
		R	MODIFY RESERVATION STATES OF RECORDS
		B	LIST RESERVATION STATES OF RECORDS
		L	LIST FILE INFORMATION
		C	COPY FILE OR FILES TO DISK
		M	COPY FILE OR FILES TO MEMORY
		F	COMPARE FILES
ZD	M	INTERROGATION OF LAPD AND SBUS STATISTICS METERS COMMANDS
		F	INTERROGATE TRANSMITTED AND RECEIVED FRAMES AND OCTETS
		I	INTERROGATE MISCELLANEOUS STATISTICAL COUNTERS
		Q	INTERROGATE Q.921 ERROR COUNTERS
		N	INTERROGATE OCCASIONAL VALUES OF LINK SET METERS
		T	INTERROGATE OCCASIONAL VALUES OF TERMINAL METERS
		U	INTERROGATE OCCASIONAL VALUES OF FUNCTIONAL UNIT METERS
		L	INTERROGATE LAPD EVENT LOGS
		E	EMPTY LAPD EVENT LOGS
		V	INTERROGATE SBUS COUNTERS
ZD	O	OPERATING SYSTEM SUPERVISION AND STATISTICS HANDLING COMMANDS
		M	MODIFY SUPERVISION PARAMETERS
		P	DISPLAY PERMANENT SUPERVISION PARAMETERS
		T	DISPLAY CURRENT SUPERVISION PARAMETERS OF UNIT
		C	MODIFY OPERATING SYSTEM ERROR COUNTER SUPERVISION PARAMETERS
		E	DISPLAY OPERATING SYSTEM ERROR COUNTER SUPERVISION PARAMETERS
		I	INTERROGATE SUPERVISION RESULT
		H	CREATE PROCESSOR TIME USAGE MEASUREMENT
		R	CREATE MEMORY USAGE MEASUREMENT
		F	CREATE FAMILY RESOURCE USAGE MEASUREMENT
		D	DELETE MEASUREMENT
		G	CHANGE STATE OF MEASUREMENT
		V	DISPLAY DEFINED MEASUREMENTS
		W	CREATE PASSIVE WARMING MEASUREMENT
		O	INTERROGATE PASSIVE WARMING STATUS
ZD	P	PREPROCESSOR MEMORY HANDLING COMMANDS
		D	DISPLAY MEMORY OF PREPROCESSOR
		S	SUBSTITUTE MEMORY OF PREPROCESSOR
		F	FILL MEMORY WITH GIVEN DATA
		I	INPUT DATA FROM PORT
		Y	DISPLAY BID / PID OF CHORUS-TYPE PREPROCESSOR
		P	DISPLAY CID / PID OF PECTUS-TYPE PREPROCESSOR
		X	DISPLAY CID / PID / MID OF  PREPROCESSOR
ZD	R	SYNCHRONIZATION UNIT HANDLING COMMANDS
		M	SET OPERATING MODE
		C	CREATE SYNCHRONIZATION INPUTS
		D	DELETE SYNCHRONIZATION INPUTS
		I	INTERROGATE SYNCHRONIZATION UNITS
		S	SELECT SPECIAL FUNCTIONS
		O	SELECT OSCILLATOR HANDLING FUNCTIONS
ZD	S	PRIMARY RATE ACCESS D-CHANNEL DATA HANDLING COMMANDS
		C	CREATE D-CHANNEL LINK SET
		D	DELETE D-CHANNEL LINK SET
		I	INTERROGATE D-CHANNEL LINK SET DATA
		E	CREATE BASE STATION CONTROLLER D-CHANNEL
		L	CREATE BSC LOGICAL UNIT D-CHANNEL
		B	INTERROGATE BASE STATION CONTROLLER D-CHANNEL DATA
		F	INTERROGATE D-CHANNEL DATA OF FUNCTIONAL UNIT
ZD	T	PRIMARY RATE ACCESS D-CHANNEL STATE MANAGEMENT COMMANDS
		C	MODIFY D-CHANNEL WORKING STATE
		I	INTERROGATE D-CHANNEL WORKING STATE
		T	MODIFY D-CHANNEL WORKING STATE OF FUNCTIONAL UNIT
		F	INTERROGATE D-CHANNEL WORKING STATE OF FUNCTIONAL UNIT
ZD	U	DISK UPDATE HANDLING COMMANDS
		P	PREVENT FILE UPDATES TO DISK
		R	RESUME FILE UPDATES TO DISK
		D	DISPLAY DISK UPDATE STATE
		Q	DISPLAY DISK UPDATE QUEUE STATE
ZD	V	DISK LOG HANDLER PROGRAM COMMANDS
		C	CREATE NEW SUBLOG FILE
		E	CLOSE SUBLOG FILE
		R	RESIZE LOGFILE
		M	MODIFY LOG FILTERING SETTINGS
		D	DELETE SUBLOG FILE
		F	CLEAR SUBLOG FILE
		I	INTERROGATE LOG FILTERING SETTINGS
		G	DISPLAY LOG DIRECTORY
		L	DISPLAY LOG DATA
		P	DISPLAY LOG SETTINGS
		T	DISPLAY LOG STATISTICS
ZE	CELLULAR RADIO NETWORK ADMINISTRATION
ZE	A	ADJACENT CELL HANDLING IN BSC COMMANDS
		C	CREATE ADJACENT CELL PARAMETERS
		D	DELETE ADJACENT CELL PARAMETERS
		M	MODIFY ADJACENT CELL PARAMETERS
		X	MODIFY C/I HANDOVER PARAMETERS
		O	OUTPUT ADJACENT CELL PARAMETERS
		T	CHECK ADJACENT CELL DATA
ZE	B	BCCH AND MOBILE ALLOCATION FREQUENCY LIST AND RA HANDLING COMMANDS
		C	CREATE BCCH FREQUENCY LIST
		D	DELETE BCCH FREQUENCY LIST
		M	MODIFY BCCH FREQUENCY LIST
		O	OUTPUT BCCH FREQUENCY LIST(S)
		E	CREATE MOBILE ALLOCATION FREQUENCY LIST
		R	DELETE MOBILE ALLOCATION FREQUENCY LIST
		T	MODIFY MOBILE ALLOCATION FREQUENCY LIST
		I	OUTPUT MOBILE ALLOCATION FREQUENCY LIST(S)
		F	CREATE ROUTING AREA
		G	DELETE ROUTING AREA
		H	MODIFY ROUTING AREA
		P	OUTPUT ROUTING AREA(S)
ZE	C	SMS CELL BROADCAST HANDLING COMMANDS
		P	DISPLAY MESSAGE(S)
		L	DISPLAY BTS WORK LOAD
ZE	E	BASE STATION CONTROLLER HANDLING COMMANDS
		M	MODIFY GENERAL BASE STATION CONTROLLER PARAMETERS
		N	MODIFY RADIO NETWORK SUPERVISION PARAMETERS
		Q	MODIFY MISCELLANEOUS PARAMETERS
		U	MODIFY DYNAMIC HOTSPOT PARAMETERS
		T	MODIFY PRIORITY LEVEL TO SUBSCRIBER TYPE RELATION
		R	PREPARE DATABASE FOR DOWNLOADING OF BACKGROUND DATA
		G	CONTROL ACTIVATION OF BACKGROUND DATA
		O	OUTPUT BASE STATION CONTROLLER PARAMETERS
		I	OUTPUT RADIO NETWORK CONFIGURATION
		L	OUTPUT TRX RADIO TIME SLOTS
		P	OUTPUT BACKGROUND DATA ACTIVATION STATES
ZE	F	BASE CONTROL FUNCTION HANDLING COMMANDS
		C	CREATE BASE CONTROL FUNCTION
		D	DELETE BASE CONTROL FUNCTION
		M	MODIFY BASE CONTROL FUNCTION PARAMETERS
		O	OUTPUT BASE CONTROL FUNCTION PARAMETERS
		S	CHANGE BASE CONTROL FUNCTION ADMINISTRATIVE STATE
		T	SET BASE CONTROL FUNCTION OUTPUTS
		X	SET BASE CONTROL FUNCTION EXTERNAL INPUT PARAMETERS
		R	RESET BASE CONTROL FUNCTION
		E	MODIFY EXTERNAL INPUT AND OUTPUT TEXT
		P	OUTPUT EXTERNAL INPUT AND OUTPUT TEXTS
ZE	G	GSM TIMER AND BSC PARAMETERS HANDLING COMMANDS
		O	OUTPUT TIMERS/PARAMETERS
		T	MODIFY TIMER
		P	MODIFY PARAMETERS
ZE	H	HANDOVER CONTROL PARAMETERS HANDLING  COMMANDS
		C	CREATE HANDOVER CONTROL PARAMETERS
		G	MODIFY GENERAL PARAMETERS
		A	MODIFY AVERAGING PARAMETERS
		S	MODIFY SIGNAL STRENGTH THRESHOLD PARAMETERS
		Q	MODIFY SIGNAL QUALITY THRESHOLD PARAMETERS
		I	MODIFY SIGNAL INTERFERENCE THRESHOLD PARAMETERS
		D	MODIFY SIGNAL INTERFERENCE THRESHOLD PARAMETERS
		N	MODIFY PARAMETERS RELATED TO ADJACENT CEL
		X	MODIFY C/I HANDOVER PARAMETERS
		Y	MODIFY INTELLIGENT UNDERLAY-OVERLAY PARAMETERS
		P	MODIFY MS SPEED PARAMETERS
		O	OUTPUT HANDOVER CONTROL PARAMETERS
ZE	M	BASE CONTROL FUNCTION MAINTENANCE MODE HANDLING COMMANDS
		B	BLOCK BASE CONTROL FUNCTION ALARM HANDLING
		U	UNBLOCK BASE CONTROL FUNCTION ALARM HANDLING
		E	LIST BASE CONTROL FUNCTIONS ON MAINTENANCE MODE
		M	MODIFY MAINTENANCE MODE PARAMETERS
		O	OUTPUT MAINTENANCE MODE PARAMETERS
ZE	O	BASE TRANSCEIVER STATION ALARMS HANDLING COMMANDS
		B	BLOCK ALARM
		U	UNBLOCK ALARM
		E	LIST BLOCKED ALARMS
		C	CHANGE ALARM CLASS
		M	MODIFY ALARM PARAMETERS
		O	OUTPUT ALARM PARAMETERS
		R	CANCEL ALARM
		H	LIST ALARM HISTORY
		L	LIST ALARMS CURRENTLY ON
ZE	Q	BASE TRANSCEIVER STATION HANDLING IN BSC COMMANDS
		C	CREATE BTS
		D	DELETE BTS
		A	MODIFY MOBILE ALLOCATION FREQUENCY LIST USAGE PARAMETERS
		B	MODIFY BCCH FREQUENCY LIST USAGE PARAMETERS
		E	MODIFY BTS IDENTIFICATION PARAMETERS
		F	MODIFY CELL ACCESS PARAMETERS
		G	MODIFY RADIO LINK CONTROL DL PARAMETERS
		H	MODIFY QUEUEING PARAMETERS
		J	MODIFY CCH CONFIGURATION PARAMETERS
		K	MODIFY INTERFERENCE AVERAGING PARAMETERS
		M	MODIFY MISCELLANEOUS PARAMETERS
		T	MODIFY TRUNK RESERVATION PARAMETERS
		V	MODIFY GPRS PARAMETERS
		X	MODIFY DATA SERVICE PARAMETERS
		Q	CHECK IUO INTERFERING CELLS
		O	OUTPUT BTS PARAMETERS
		U	CHANGE SEGMENT OF BTS
		S	CHANGE BTS ADMINISTRATIVE STATE
ZE	R	TRANSCEIVER DATA HANDLING COMMANDS
		C	CREATE TRANSCEIVER
		D	DELETE TRANSCEIVER
		M	MODIFY TRANSCEIVER AND RADIO TIME SLOT PARAMETERS
		T	MODIFY TRANSCEIVER BINARY OUTPUTS
		Y	MODIFY TRANSCEIVER UNDERLAY-OVERLAY PARAMETERS
		O	OUTPUT TRANSCEIVER PARAMETERS
		S	CHANGE TRANSCEIVER AND RADIO TIME SLOT STATE
ZE	S	ABIS INTERFACE CONFIGURATION COMMANDS
ZE	T	TRUNK RESERVATION DECISION TABLE HANDLING COMMANDS
		C	CREATE DECISION THRESHOLD TABLE
		D	DELETE DECISION THRESHOLD TABLE
		M	MODIFY DECISION THRESHOLD PARAMETERS
		O	OUTPUT DECISION THRESHOLD PARAMETERS
ZE	U	POWER CONTROL PARAMETER HANDLING COMMANDS
		C	CREATE POWER CONTROL PARAMETERS
		G	MODIFY GENERAL PARAMETERS
		A	MODIFY AVERAGING PARAMETERS
		M	MODIFY DATA SERVICE PARAMETERS
		Q	MODIFY SIGNAL QUALITY THRESHOLD PARAMETERS
		S	MODIFY SIGNAL STRENGTH THRESHOLD PARAMETERS
		O	OUTPUT POWER CONTROL PARAMETERS
ZE	V	BCF HW DATABASE HANDLING COMMANDS
		C	CREATE BCF HW DATABASE
		D	DELETE BCF HW DATABASE
		A	ATTACH HW DATABASE TO BCF
		E	DETACH HW DATABASE FROM BCF
		V	ACTIVATE BCF HW DATABASE
		S	REPLACE HW DATABASE
		T	LIST BCFs ATTACHED TO SAME HW DATABASE
		L	LIST EXISTING BCF HW DATABASES
		O	LIST HW DATABASE CONFIGURATION OF BCF
		U	UPLOAD HW DATABASE FILE(S)
		R	ERASE BCF NON-VOLATILE MEMORY
ZE	W	BCF SOFTWARE HANDLING COMMANDS
		C	CREATE BCF SOFTWARE BUILD
		D	DELETE BCF SOFTWARE BUILD
		A	ATTACH SOFTWARE BUILD TO BCF
		E	DETACH SOFTWARE BUILD FROM BCF
		V	ACTIVATE BCF SOFTWARE BUILD
		H	CHANGE STATUSES OF TWO BCF SOFTWARE BUILDS
		S	SET OR REMOVE INITIAL SOFTWARE BUILD
		I	LIST BCF SOFTWARE HANDLING SYSTEM ACTIVITIES
		L	LIST EXISTING BCF SOFTWARE BUILDS
		O	LIST SOFTWARE CONFIGURATION OF BCF
		P	LIST BCF SOFTWARE BUILD CONTENTS
ZE	X	POSITION BASED SERVICES HANDLING COMMANDS
		N	MODIFY SMLC PARAMETERS
		Q	OUTPUT SMLC PARAMETERS
		C	CREATE LCS ELEMENT
		D	DELETE LCS ELEMENT
		M	MODIFY LCS ELEMENT PARAMETERS
		O	OUTPUT LCS ELEMENT PARAMETERS
		A	CREATE LMU AREA
		R	DELETE LMU AREA
		B	MODIFY LMU AREA PARAMETERS
		I	OUTPUT LMU AREA PARAMETERS
		E	CREATE RIT TRANSFER TABLE
		F	DELETE RIT TRANSFER TABLE
		G	MODIFY RIT TRANSFER TABLE PARAMETERS
		P	OUTPUT RIT TRANSFER TABLE PARAMETERS
		H	CREATE REPEATER
		K	DELETE REPEATER
		T	MODIFY REPEATER PARAMETERS
		L	OUTPUT REPEATER PARAMETERS
ZE	Y	HUNTING ORDER HANDLING COMMANDS
		I	INTERROGATE SPEECH CODEC POOL LIST(S
		M	MODIFY SPEECH CODEC POOL LIST
		R	RESTORE SPEECH CODEC DEFAULT LISTS
ZF	FRAME RELAY ADMINISTRATION
ZF	N	FRAME RELAY NODE PARAMETER HANDLING COMMANDS
		S	MODIFY LOCAL BEARER CHANNEL SIGNALLING PARAMETERS
		O	INTERROGATE LOCAL BEARER CHANNEL SIGNALLING PARAMETERS
ZF	U	FRAME RELAY BEARER CHANNEL HANDLING
		C	CREATE FRAME RELAY BEARER CHANNEL
		M	MODIFY FRAME RELAY BEARER CHANNEL DATA
		D	DELETE FRAME RELAY BEARER CHANNEL
		I	INTERROGATE FRAME RELAY BEARER CHANNEL DATA
ZF	W	NETWORK SERVICE VIRTUAL CONNECTION HANDLING COMMANDS
		C	CREATE NETWORK SERVICE VIRTUAL CONNECTION
		D	DELETE NETWORK SERVICE VIRTUAL CONNECTION
		M	MODIFY NETWORK SERVICE VIRTUAL CONNECTION
		S	CHANGE THE STATE OF NETWORK SERVICE VIRTUAL CONNECTION
		O	OUTPUT THE NETWORK SERVICE VIRTUAL CONNECTION DATA
ZI	I/O SYSTEM ADMINISTRATION
ZI	A	MMI SYSTEM AUTHORITY HANDLING COMMANDS
		A	CREATE OR MODIFY PROFILE
		R	DELETE PROFILE
		H	CREATE USER ID
		D	DELETE USER ID
		E	ATTACH PROFILE TO USER ID OR TERMINAL
		G	CHANGE OWN PASSWORD
		S	CHANGE PASSWORD OF OTHER USER ID
		F	CHANGE SERVICE TERMINAL PASSWORD
		Q	RESET LOGIN DELAYS
		X	MODIFY MML SESSION TIME LIMIT
		K	CHANGE ENCRYPTION METHOD
		M	CHANGE COMMAND DEFINITIONS
		I	INTERROGATE USER IDS, TERMINALS AND PROFILES
		T	INTERROGATE COMMAND DEFINITIONS
		L	INTERROGATE ALLOWED COMMANDS
		B	BLOCK/UNBLOCK COMMAND
		O	INTERROGATE BLOCKED COMMANDS
ZI	B	I/O FILE BACKUP COMMANDS
		B	COPY BYTES FROM STATISTICAL TAPE TO HARD DISK
		C	COPY MASS MEMORY FILES
		D	DELETE LAST FILE SET OF CTU
		F	MOVE DATA FROM DISK BUFFER OF CTU
		P	DUMP DATA FROM TAPE
		R	RESTORE DATA FROM TAPE TO LOGICAL FILE
		T	TYPE FILE
		X	DISPLAY CONTENTS OF TAPE
ZI	C	COMMAND CALENDAR HANDLING COMMANDS
		I	ADD NEW COMMAND CALENDAR TASK
		M	MODIFY COMMAND CALENDAR TASK
		D	DELETE COMMAND CALENDAR TASK
		L	LIST CALENDAR
		T	TEST COMMAND CALENDAR TASK EXECUTION
		B	BLOCK OR UNBLOCK COMMAND CALENDAR TASK
		S	STOP COMMAND FILE EXECUTION
ZI	D	DISK COMMAND FILE EXECUTION COMMAND COMMANDS
		E	EXECUTE COMMAND FILE
		S	STOP COMMAND FILE EXECUTION
		L	LIST COMMAND FILE
		X	EXECUTE REMOTE COMMAND
ZI	E	DISK FILE OPERATIONS COMMANDS
		E	EDIT DISK FILE
ZI	F	VIRTUAL DATA STORING DEVICE HANDLING COMMANDS
		S	SET DISK FILE STATUS
		A	SET DISK ALARM LIMITS
		F	DEFINE FILE AND STORING RELATED PARAMETERS
		N	INITIALIZE VDS DEVICE
		T	DEFINE TIME CONTROL FOR CHANGING DISK FILES
		M	MODIFY FTAM ATTRIBUTES
		H	DEFINE CONTROL FILE HANDLING
		Q	DEFINE Q3 TRANSFER UP READY PARAMETERS
		C	COPY DATA FILES
		O	DISPLAY CONTROL FILES
		P	DISPLAY FILE STATUS MAP
		I	INTERROGATE DISK FILE INFORMATION
ZI	G	MML COMMAND LOG HANDLING COMMANDS
		O	DISPLAY MML COMMAND LOG
		K	CLOSE MML COMMAND LOG FILE
ZI	I	I/O CONFIGURATION HANDLING COMMANDS
		D	DISPLAY INFORMATION OF GIVEN LOGICAL FILE
		S	CHANGE OBJECT CONNECTED TO LOGICAL FILE
		L	LIST LOGICAL FILES CONNECTED TO GIVEN OBJECT
		C	CHANGE OBJECT TO ANOTHER IN ALL LOGICAL FILES
		F	CREATE LOGICAL FILE
		P	CREATE SPARE LOGICAL FILE
		R	REMOVE LOGICAL FILE
		I	LINK PHYSICAL DISK FILE TO LOGICAL FILE
		G	CHANGE SIGNALLED PROCESS
ZI	M	MAGNETIC TAPE HANDLING
		P	PREMARK MAGNETIC TAPE
		O	OPEN FILE ON MAGNETIC TAPE
		C	CLOSE FILE ON MAGNETIC TAPE
		R	RELEASE MAGNETIC TAPE
		D	DISPLAY STATUS OF UNIT(S) AND TAPE(S)
		T	CHANGE MAGNETIC TAPE
		F	REOPEN FILE ON MAGNETIC TAPE
		I	IDENTIFY TAPE AND RESERVE UNIT
		S	SET TAPE TYPE
		E	RESET TAPE UNIT
		M	MODIFY/INTERROGATE TAPE CODING
ZI	O	NETWORK USER AUTHORITY DATA HANDLING COMMANDS
		A	ADD USER PROFILE
		M	ADD USER ACCESS RIGHTS
		R	REMOVE USER ACCESS RIGHTS
		E	INTERROGATE NETWORK ELEMENT USERS
		I	INTERROGATE USER PROFILE
ZI	P	BATCH COPY HANDLING COMMANDS
		I	INTERROGATE GENERAL COPY TASK INFORMATION
		P	DISPLAY DETAILED COPY TASK LOG
		S	START BACKUP COPY TASK
		T	TERMINATE ONGOING COPY TASK
		X	DISPLAY BACKUP COPIES ON REMOVABLE DISK
ZI	Q	DISK OPTIMIZATION CONTROL COMMANDS
		C	CONFIGURE THE DISK CACHE
		S	DISPLAY CACHE STATISTICS
		V	HANDLE DISK WRITE VERIFICATION
ZI	R	SECURITY REPORTING HANDLING COMMANDS
		M	MODIFY CRITICAL LIMITS
		R	RESET LONG TERM COUNTERS
		T	SET COUNTER REPORT OUTPUT TIME
		I	INTERROGATE COUNTER REPORT OUTPUT PARAMETERS
		O	DISPLAY DETAILED REPORT
		P	PRINT COUNTER REPORT
ZI	S	I/O DEVICE WORKING STATE COMMANDS
		C	CHANGE I/O DEVICE STATE
		I	INTERROGATE I/O DEVICE INFO
		L	LIST I/O DEVICES IN SPECIFIED STATE
		M	MODIFY SPARE DEVICE OF I/O DEVICE
		K	MODIFY/INTERROGATE SCSI ADDRESS OF MTU
		F	CHANGE FUNCTIONAL MODE OF CTU
ZI	T	TERMINAL PARAMETERS HANDLING COMMANDS
		I	INTERROGATE TERMINAL PARAMETERS
		M	MODIFY TERMINAL PARAMETERS
		F	SET TERMINAL OPERATION MODE
ZI	W	DISK FILE AND DIRECTORY HANDLING
		B	HANDLE BAD BLOCKS
		C	CREATE FILE
		D	DELETE FILE
		E	EMPTY FILE
		F	INTERROGATE/CHANGE DEFAULT VERSION
		I	INITIALIZE DISK
		K	INITIALIZE DIRECTORY
		L	CREATE DIRECTORY
		M	DELETE DIRECTORY
		N	RENAME FILE
		P	PACK DISK
		Q	INTERROGATE/MODIFY DISK CONFIGURATION
		S	SET FILE ATTRIBUTES
		X	DISPLAY DIRECTORY
		Y	INTERROGATE/CHANGE DEFAULT SETTINGS
ZI	X	DISK FILE COMPRESSION HANDLING MML COMMANDS
		F	COMPRESS FILE(S) TO ZIP ARCHIVE
		X	EXTRACT FILE(S) FROM ZIP ARCHIVE
		L	LIST CONTENTS OF ZIP ARCHIVE
		C	COMPRESS FILE TO GZIP ARCHIVE
		E	EXTRACT FILE FROM GZIP ARCHIVE
		I	LIST CONTENTS OF GZIP ARCHIVE(S)
ZN	SS7 NETWORK ADMINISTRATION
ZN	A	GLOBAL TITLE RESULT HANDLING COMMANDS
		A	CREATE GLOBAL TITLE MODIFICATION DATA
		C	CREATE TRANSLATION RESULT
		D	DELETE TRANSLATION RESULT
		I	INTERROGATE TRANSLATION RESULTS
		M	MODIFY TRANSLATION RESULT
		R	DELETE GLOBAL TITLE MODIFICATION DATA
		S	MODIFY GLOBAL TITLE MODIFICATION DATA
		X	INTERROGATE GLOBAL TITLE MODIFICATION DATA
ZN	B	SCCP GLOBAL TITLE ANALYSIS HANDLING COMMANDS
		C	CREATE OR ADD ANALYSIS
		D	DELETE OR REMOVE ANALYSIS
		I	INTERROGATE OR SEARCH ANALYSIS
		J	INTERROGATE ROOTS OF ANALYSIS TREES
ZN	C	SIGNALLING LINK DATA HANDLING COMMANDS COMMANDS
		C	CREATE SIGNALLING LINK
		M	MODIFY SIGNALLING LINK
		D	DELETE SIGNALLING LINK
		I	INTERROGATE SIGNALLING LINK DATA
		L	CHANGE PARAMETER SET
		O	EXCHANGE PARAMETER SET OF SIGNALLING LINKS
ZN	E	SIGNALLING NETWORK STATE INTERROGATION COMMANDS
		R	INTERROGATE SIGNALLING ROUTE SET STATES
		S	INTERROGATE SIGNALLING LINK SET STATES
		L	INTERROGATE SIGNALLING LINK STATES
		T	INTERROGATE NETWORK ITEM STATES
		O	INTERROGATE SIGNALLING POINT LOAD SHARING
		P	INTERROGATE PROHIBITED STP MESSAGES
		J	RUN SIGNALLING ROUTING TEST
ZN	F	SCCP DATA HANDLING COMMANDS
		D	DEFINE SCCP FOR SIGNALLING POINT
		E	DEFINE SCCP FOR SIGNALLING POINTS WITH SUBSYSTEMS COPY
		R	REMOVE SCCP FROM SIGNALLING POINTS
		A	ADD REPLICATIVE SIGNALLING POINT
		S	REMOVE REPLICATIVE SIGNALLING POINT
		B	ADD SUBSYSTEMS TO SIGNALLING POINTS
		T	REMOVE SUBSYSTEM FROM SIGNALLING POINTS
		C	ADD REPLICATIVE SUBSYSTEM
		U	REMOVE REPLICATIVE SUBSYSTEM
		I	INTERROGATE SCCP DATA OF SIGNALLING POINTS
		J	INTERROGATE SUBSYSTEMS DATA OF SIGNALLING POINTS
		L	CHANGE SCCP SIGNALLING POINT PARAMETER SET
		M	CHANGE SUBSYSTEM PARAMETER SET
		N	EXCHANGE PARAMETER SET OF SCCP SIGNALLING POINT
		O	EXCHANGE PARAMETER SET OF SUBSYSTEM
		P	CHANGE SUBSYSTEM TEST STATUS
ZN	G	SCCP STATE HANDLING COMMANDS
		C	CHANGE SCCP STATE
		D	CHANGE REPLICATION STATE
		I	INTERROGATE SCCP STATE
ZN	H	SCCP SUBSYSTEM STATE HANDLING COMMANDS
		C	CHANGE SUBSYSTEM STATE
		D	CHANGE SUBSYSTEM REPLICATION STATE
		I	INTERROGATE SUBSYSTEM STATE
		J	INTERROGATE SUBSYSTEM DISTRIBUTION DATA
ZN	L	SIGNALLING LINK STATE HANDLING COMMANDS
		C	CHANGE SIGNALLING LINK STATE
		D	DENY ACTIVATION OF SIGNALLING LINKS
		A	ALLOW ACTIVATION OF SIGNALLING LINKS
		I	INTERROGATE SIGNALLING LINK STATES
		T	TEST SIGNALLING DATA LINK
		O	INTERROGATE SIGNALLING DATA LINK TEST
		J	RUN SIGNALLING LINK ROUTING TEST
ZN	M	CCS7 LEVEL 3 PARAMETERS HANDLING COMMANDS
		M	MODIFY CCS7 LEVEL 3 PARAMETER
		I	INTERROGATE CCS7 LEVEL 3 PARAMETERS
		C	MODIFY CCS7 NETWORK SPECIFIC PARAMETER
		O	INTERROGATE CCS7 NETWORK SPECIFIC PARAMETERS
ZN	N	SIGNALLING ROUTE SET PARAMETER SET HANDLING COMMANDS
		C	CREATE SIGNALLING ROUTE SET PARAMETER SET
		E	COPY SIGNALLING ROUTE SET PARAMETER SET
		M	MODIFY SIGNALLING ROUTE SET PARAMETER SET
		N	CHANGE SIGNALLING ROUTE SET PARAMETER SET NAME
		D	DELETE SIGNALLING ROUTE SET PARAMETER SET
		I	INTERROGATING SIGNALLING ROUTE SET PARAMETER SETS
ZN	O	SIGNALLING LINK PARAMETER SET HANDLING COMMANDS
		C	CREATE SIGNALLING LINK PARAMETER SET
		E	COPY SIGNALLING LINK PARAMETER SET
		M	MODIFY SIGNALLING LINK PARAMETER SET
		N	CHANGE SIGNALLING LINK PARAMETER SET NAME
		D	DELETE SIGNALLING LINK PARAMETER SET
		I	INTERROGATE SIGNALLING LINK PARAMETER SETS
ZN	P	SERVICE INFORMATION DATA HANDLING COMMANDS
		C	CREATE SERVICE
		M	MODIFY SERVICE
		D	DELETE SERVICE
		I	INTERROGATE SERVICES
		U	UPDATE STP-SERVICE
ZN	R	SIGNALLING ROUTE SET DATA HANDLING COMMANDS
		P	MODIFY OWN SIGNALLING POINT DATA
		C	CREATE SIGNALLING ROUTE SET
		B	MODIFY DATA OF SIGNALLING ROUTE SET
		D	DELETE SIGNALLING ROUTE SET
		A	ADD SIGNALLING ROUTE TO ROUTE SET
		R	DELETE SIGNALLING ROUTE FROM ROUTE SET
		E	CHANGE SIGNALLING ROUTE PRIORITY
		N	CHANGE SIGNALLING POINT NAME
		I	INTERROGATE SIGNALLING POINT DATA
		S	CHANGE STP ACCESS
		T	INTERROGATE STP ACCESS
		X	EXCHANGE ADJACENT SIGNALLING POINT CODE
		V	VERIFY OF MTP ROUTING DATA CHAINS
		F	REPAIR OF MTP ROUTING DATA CHAINS
ZN	S	SIGNALLING LINK SET DATA HANDLING COMMANDS
		C	CREATE SIGNALLING LINK SET
		A	ADD SIGNALLING LINK TO LINK SET
		R	DELETE SIGNALLING LINK FROM LINK SET
		N	CHANGE SIGNALLING LINK SET NAME
		S	CHANGE SIGNALLING LINK CODE
		D	DELETE SIGNALLING LINK SET
		I	INTERROGATE SIGNALLING LINK SET DATA
		T	CHANGE SIGNALLING LINK TEST STATUS
ZN	V	SIGNALLING ROUTE STATE HANDLING COMMANDS
		C	CHANGE SIGNALLING ROUTE STATE
		D	DENY ACTIVATION OF SIGNALLING ROUTE
		A	ALLOW ACTIVATION OF SIGNALLING ROUTE
		I	INTERROGATE SIGNALLING ROUTE STATES
ZO	SUPPLEMENTARY SS7 NETWORK ADMINISTRATION
ZO	B	SCCP BROADCAST STATUS HANDLING COMMANDS COMMANDS
		M	MODIFY BROADCAST STATUS OF SCCP SIGNALLING POINTS
		I	INTERROGATE BROADCAST STATUS OF SCCP SIGNALLING POINTS
		C	MODIFY LOCAL BROADCAST STATUS OF SCCP SUBSYSTEMS
		L	INTERROGATE LOCAL BROADCAST STATUS OF SCCP SUBSYSTEMS
ZO	C	SCCP PARAMETER SET HANDLING COMMANDS
		C	CREATE SCCP SIGNALLING POINT PARAMETER SET
		A	CREATE SCCP SUBSYSTEM PARAMETER SET
		E	COPY SCCP SIGNALLING POINT PARAMETER SET
		F	COPY SCCP SUBSYSTEM PARAMETER SET
		M	MODIFY SCCP SIGNALLING POINT PARAMETER SET
		N	MODIFY SCCP SUBSYSTEM PARAMETER SET
		R	CHANGE PARAMETER SET NAME
		D	DELETE SCCP SIGNALLING POINT PARAMETER SET
		K	DELETE SCCP SUBSYSTEM PARAMETER SET
		I	INTERROGATE SCCP SIGNALLING POINT PARAMETER SETS
		J	INTERROGATE SCCP SUBSYSTEM PARAMETER SETS
		H	HELP TEXT FOR SCCP SIGNALLING POINT PARAMETERS
		L	HELP TEXT FOR SCCP SUBSYSTEM PARAMETERS
ZO	D	SCCP SCREENING HANDLING COMMANDS
		C	COPY SCCP SCREENING DATA FROM MTP
		I	INTERROGATE SCCP SCREENING DATA
		M	MODIFY SCCP SCREENING
		S	MODIFY SCCP SCREENING STATUS
ZO	I	MANAGEMENT OF TRAFFIC MATRIX MEASUREMENT FOR MTP COMMANDS
		S	DEFINE MAXIMUM COUNTS OF INDEXES
		I	INTERROGATE MAXIMUM COUNTS OF INDEXES
		O	CONNECT OP/DP INDEX TO SIGNALLING POINT
		E	DELETE OP/DP INDEX
		D	LIST ALL OP/DP INDEXES
		A	DELETE ALL OP/DP INDEXES
		U	CONNECT SI INDEX TO USER PART
		C	DELETE SI INDEX
		P	LIST ALL SI INDEXES
		L	DELETE ALL SI INDEXES
ZO	L	INTERROGATION OF SIGNALLING LINK STATISTICS METERS COMMANDS
		P	INTERROGATE SIGNALLING LINK PERFORMANCE METERS
		A	INTERROGATE SIGNALLING LINK AVAILABILITY METERS
		U	INTERROGATE SIGNALLING LINK UTILIZATION METERS
		T	INTERROGATE SIGNALLING LINK LOAD
		L	INTERROGATE SIGNALLING LINK EVENT LOGS
		E	EMPTY SIGNALLING LINK EVENT LOGS
ZO	M	INTERROGATION OF AUXIALIARY MTP STATISTICS METERS COMMANDS
		Q	INTERROGATE LEVEL 3 AUXILIARY METERS
		T	INTERROGATE SIGNALLING LINK TERMINAL METERS
		I	INTERROGATE MTP LEVEL 2 METERS
		S	INTERROGATE ATM BASED SIGNALLING LINK SAAL METERS
ZO	N	INTERROGATION OF SIGNALLING NETWORK STATISTICS METERS COMMANDS
		A	SIGNALLING LINK SET AND ROUTE SET AVAILABILITY METERS
		S	SIGNALLING POINT STATUS METERS
		P	SIF AND SIO METERS HANDLED WITH SP
		I	SIF AND SIO METERS HANDLED WITH SIO
		T	SIF, SIO AND MSU METERS HANDLED WITH OPC, DPC AND SIO
		E	EMPTY SIGNALLING POINT EVENT LOGS
		L	INTERROGATE SIGNALLING POINT EVENT LOGS
ZO	S	STATES OF SS7 STATISTICS COMMANDS
		A	ACTIVATE SS7 STATISTICS AND REPORTS
		D	DEACTIVATE SS7 STATISTICS AND REPORTS
		E	INTERROGATE REPORTING STATUS OF SCCP SUBSYSTEMS
		F	MODIFY REPORTING STATUS OF SCCP SUBSYSTEMS
		I	INTERROGATE STATES OF SS7 STATISTICS
		J	INTERROGATE REPORTING STATUS OF SIGNALLING LINKS
		K	INTERROGATE REPORTING STATUS OF SIGNALLING POINTS
		L	MODIFY REPORTING STATUS OF SIGNALLING LINKS
		M	MODIFY SS7 MEASUREMENT REPORT PARAMETERS
		N	MODIFY REPORTING STATUS OF SIGNALLING POINTS
		R	INTERROGATE SS7 MEASUREMENT REPORT PARAMETERS
		G	MODIFY STATES OF INTERVAL LOG REPORTS
		Q	INTERROGATE STATES OF INTERVAL LOG REPORTS
ZO	T	INTERROGATION OF SCCP AND TC STATISTICS METERS COMMANDS
		N	SCCP SIGNALLING POINT METERS
		S	SCCP SUBSYSTEM METERS
		J	SCCP SUBSYSTEM METERS OF SIGNALLING POINT
		A	SCCP LOCAL SUBSYSTEM AVAILABILITY METERS
		I	INTERROGATE SCCP SINGLE METERS
		G	INTERROGATE SCCP SEGMENTATION AND REASSEMBLY ERROR METERS
		Q	SCCP QUALITY OF SERVICE METERS
		E	EMPTY SCCP OR TC EVENT LOG
		O	INTERROGATE SCCP SIGNALLING POINT EVENT LOG
		L	INTERROGATE SCCP SUBSYSTEM EVENT LOG
		R	INTERROGATE SCCP MESSAGE HANDLING FAILURE LOG
		U	INTERROGATE TC UTILIZATION METERS
		T	INTERROGATE TC TRANSACTION METERS
		P	INTERROGATE TC FAULT METERS
		F	INTERROGATE TC EVENT LOG
ZQ	O&M NETWORK ADMINISTRATION
ZQ	B	NETWORK ADDRESS AND NSAP DATA HANDLING COMMANDS
		C	CREATE NETWORK ADDRESS
		D	DELETE NETWORK ADDRESS
		I	INTERROGATE NETWORK ADDRESS DATA
		N	CREATE NSAP
		M	MODIFY NSAP DATA
		R	DELETE NSAP
		T	ATTACH NSAP TO NETWORK ADDRESS
		F	DETACH NSAP FROM NETWORK ADDRESS
		H	SET DEFAULT VALUES FOR ISO DCC AND ISO 6253-ICD NSAP
		G	CHANGE NSAP STATE
		L	INTERROGATE NETWORK NSAP DATA
ZQ	C	PHYSICAL CHANNEL DATA HANDLING COMMANDS
		C	CREATE PHYSICAL CHANNEL THROUGH DIGITAL TERMINAL
		S	CREATE PHYSICAL CHANNEL THROUGH ANALOG TERMINAL
		M	MODIFY PHYSICAL CHANNEL THROUGH DIGITAL TERMINAL
		U	MODIFY PHYSICAL CHANNEL THROUGH ANALOG TERMINAL
		D	DELETE PHYSICAL CHANNEL
		I	INTERROGATE PHYSICAL CHANNEL DATA
ZQ	D	OSI ENVIRONMENT APPLICATION DATA HANDLING COMMANDS
		L	CREATE LOCAL OSI APPLICATION
		R	CREATE REMOTE OSI APPLICATION
		M	MODIFY LOCAL OSI APPLICATION DATA
		H	MODIFY REMOTE OSI APPLICATION DATA
		N	MODIFY OSI APPLICATION NAME
		D	DELETE OSI APPLICATION
		I	INTERROGATE OSI APPLICATION DATA
		A	ADD SERVICE PROFILE TO OSI APPLICATION
		C	MODIFY SERVICE PROFILE OF OSI APPLICATION
		E	DETACH SERVICE PROFILE FROM OSI APPLICATION
		T	ATTACH SECONDARY SELECTOR GROUP TO OSI APPLICATION
		F	DETACH OR MODIFY SECONDARY SELECTOR GROUP
		G	CHANGE OSI APPLICATION STATE
ZQ	E	OSI ENVIRONMENT CONNECTIONLESS NETWORK SERVICE HANDLING COMMANDS
		C	CREATE CLNS
		M	MODIFY CLNS DATA
		A	ADD MANUAL AREA ADDRESS TO CLNS
		R	REMOVE MANUAL AREA ADDRESS FROM CLNS
		N	MODIFY CLNS NAME
		F	MODIFY CLNS PARAMETERS
		T	RESTART CLNS
		G	CHANGE CLNS STATE
		D	DELETE CLNS
		H	ACCEPT NEW CLNS
		I	INTERROGATE CLNS DATA
ZQ	F	OSI FILE SERVICES
		A	COPY FILE
		C	CREATE FILE
		D	DELETE FILE
		L	LIST FILE DIRECTORY
		M	MODIFY FILE ATTRIBUTES
ZQ	G	PHYSICAL CHANNEL GROUP DATA HANDLING COMMANDS
		C	CREATE PHYSICAL CHANNEL GROUP
		A	ADD PHYSICAL CHANNEL TO PHYSICAL CHANNEL GROUP
		R	DELETE PHYSICAL CHANNEL FROM PHYSICAL CHANNEL GROUP
		N	CHANGE PHYSICAL CHANNEL GROUP NAME
		M	CHANGE PHYSICAL CHANNEL DATA
		D	DELETE PHYSICAL CHANNEL GROUP
		I	INTERROGATE PHYSICAL CHANNEL GROUP DATA
ZQ	H	ETHERNET TERMINAL DATA HANDLING COMMANDS
		C	CREATE ETHERNET TERMINAL DATA
		M	MODIFY ETHERNET TERMINAL DATA
		D	DELETE ETHERNET TERMINAL DATA
		I	INTERROGATE ETHERNET TERMINAL DATA
ZQ	L	OSI ENVIRONMENT LINKAGE HANDLING COMMANDS
		C	CREATE X.25 LINKAGE
		L	CREATE BROADCAST LINKAGE
		M	MODIFY X.25 LINKAGE DATA
		R	MODIFY BROADCAST LINKAGE
		G	CHANGE LINKAGE STATE
		F	MODIFY LINKAGE PARAMETERS
		D	DELETE LINKAGE
		I	INTERROGATE LINKAGE DATA
		A	ADD MANUAL ES ADJACENCY TO LINKAGE
		E	REMOVE MANUAL ES ADJACENCY FROM LINKAGE
		P	INTERROGATE LINKAGE ADJACENCY INFORMATION
ZQ	N	O&M NETWORK HANDLING
		A	ADD NEW O&M CONNECTION
		C	CHANGE WORKING STATE OF O&M CHANNEL
		D	DELETE O&M CONNECTION
		I	INTERROGATE O&M NETWORK CONFIGURATION
		M	MODIFY O&M CONNECTION
		N	INTERROGATE OCCASIONAL VALUES OF O&M CHANNEL METERS
		S	DISPLAY MML SESSIONS
ZQ	Q	ACCESS CONTROL DATA HANDLING COMMANDS
		C	ADD SNPA TO OSI ACCESS CONTROL LIST
		M	MODIFY OSI ACCESS CONTROL METHOD
		D	DELETE SNPA FROM OSI ACCESS CONTROL LIST
		I	INTERROGATE OSI ACCESS CONTROL DATA
ZQ	R	TCP/IP STACK DATA HANDLING COMMANDS
		N	CONFIGURE NETWORK INTERFACE
		G	REMOVE NETWORK INTERFACE
		W	FORCE INTERFACE SWITCHOVER
		I	INTERROGATE NETWORK INTERFACE
		T	CONFIGURE TCP/IP PARAMETERS
		H	INTERROGATE TCP/IP PARAMETERS
		C	CREATE STATIC ROUTE
		D	DELETE STATIC ROUTE
		L	INTERROGATE STATIC ROUTES
		K	CONFIGURE DNS PARAMETERS
		J	INTERROGATE DNS PARAMETERS
		R	RESET TCP/IP NETWORK COMMUNICATIONS ENVIRONMENT
		F	DISTRIBUTE CONFIGURATION FILE
		X	TEST HOST REACHABILITY (PING)
		S	INTERROGATE NETWORK STATUS
ZQ	S	PHYSICAL CHANNEL STATE HANDLING
		C	CHANGE PHYSICAL CHANNEL STATE
		I	INTERROGATE PHYSICAL CHANNEL STATES
ZQ	T	ANALOG TERMINAL DATA HANDLING COMMANDS
		C	CREATE ANALOG TERMINAL DATA
		M	MODIFY ANALOG TERMINAL DATA
		D	DELETE ANALOG TERMINAL DATA
		I	INTERROGATE ANALOG TERMINAL DATA
ZQ	U	BSS TRANSMISSION EQUIPMENT HANDLING COMMANDS
		S	START REMOTE SESSION
		E	EXECUTE REMOTE COMMAND
		A	ADD EQUIPMENT DATA
		D	DELETE EQUIPMENT DATA
		M	MODIFY EQUIPMENT DATA
		P	DISPLAY EQUIPMENT DATA
		F	HANDLE EQUIPMENT COLLECTION AND CHECKSUM POLLING
		B	ADD OBJECT TO TRANSMISSION MEASUREMENT
		R	REMOVE OBJECT FROM TRANSMISSION MEASUREMENT
		I	INTERROGATE TRANSMISSION MEASUREMENT OBJECTS
		C	CREATE TRANSMISSION EQUIPMENT SOFTWARE BUILD
		G	DELETE TRANSMISSION EQUIPMENT SOFTWARE BUILD
		T	ATTACH EQUIPMENT TO SOFTWARE BUILD
		U	DETACH EQUIPMENT FROM SOFTWARE BUILD
		H	HANDLE SOFTWARE BUILD DATA
		L	LIST SOFTWARE BUILD DATA
ZQ	V	VIRTUAL TERMINAL COMMUNICATION COMMANDS
		C	CONNECT
		I	INTERROGATE PAD PARAMETERS
		M	MODIFY PAD PARAMETERS
		P	DISPLAY CONNECTION INFORMATION
		D	DISCONNECT
ZQ	W	Q1 INTERFACE HANDLING COMMANDS
		C	CREATE SERVICE CHANNEL
		D	DELETE SERVICE CHANNEL
		M	MODIFY SERVICE CHANNEL CONFIGURATION
		S	SET SERVICE CHANNEL STATE
		I	INTERROGATE SERVICE CHANNEL CONFIGURATION
		A	ADD EQUIPMENT TO SERVICE CHANNEL
		R	REMOVE EQUIPMENT FROM SERVICE CHANNEL
		G	CHANGE EQUIPMENT INFORMATION
		F	MODIFY BTS Q1 BUS PARAMETER
		L	LIST EQUIPMENT
ZQ	X	X25 CONFIGURATION PARAMETERS HANDLING COMMANDS
		C	CREATE X25 CONFIGURATION PARAMETER SET DATA
		M	MODIFY X25 CONFIGURATION PARAMETER SET DATA
		F	ADD AND REMOVE X25 INTERFACE FACILITIES
		D	DELETE X25 CONFIGURATION PARAMETER SET DATA
		I	INTERROGATE X25 CONFIGURATION PARAMETERS
ZR	ROUTING ADMINISTRATION
ZR	B	SEMIPERMANENT BROADBAND CONNECTIONS HANDLING
		A	CREATE BROADBAND CONNECTION
		B	CREATE POINT-TO-MULTIPOINT BROADBAND CONNECTION
		I	INTERROGATE SEMIPERMANENT BROADBAND CONNECTIONS
		M	MODIFY POINT-TO-MULTIPOINT BROADBAND CONNECTION
		P	DELETE BROADBAND CONNECTION
		R	DELETE POINT-TO-MULTIPOINT BROADBAND CONNECTION
		X	UPDATE BOOKED TIME
ZR	C	CIRCUIT GROUP HANDLING COMMANDS
		C	CREATE CIRCUIT GROUP
		A	ADD CIRCUITS TO CIRCUIT GROUP
		N	MODIFY CIRCUIT GROUP
		M	MODIFY ADDITIONAL CIRCUIT GROUP PARAMETERS
		I	INTERROGATE CIRCUIT GROUP
		R	REMOVE CIRCUITS FROM CIRCUIT GROUP
		D	DELETE CIRCUIT GROUP
ZR	R	ROUTE HANDLING COMMANDS
		C	CREATE ROUTE
		A	ADD CIRCUIT GROUP
		M	MODIFY ROUTE
		D	DELETE ROUTE / CIRCUIT GROUP
		I	INTERROGATE ROUTE
ZT	TRAFFIC ADMINISTRATION
ZT	P	GSM MEASUREMENT HANDLING COMMANDS
		M	MODIFY GSM MEASUREMENT CHARACTERISTICS
		I	INTERROGATE GSM MEASUREMENT
		S	START GSM MEASUREMENT
		E	STOP GSM MEASUREMENT
ZT	V	BSC MEASUREMENTS COUNTERS INQUIRY COMMANDS
		I	INQUIRE AND OUTPUT COUNTERS
		O	OUTPUT COUNTERS
		S	SHOW DESCRIPTION OF THE COUNTERS
		R	RESET THE COUNTERS
ZU	UNIT ADMINISTRATION
ZU	B	SINGLE RADIO NETWORK TEST HANDLING COMMANDS
		E	SYNCHRONIZE BCCH FOR TERMINATING TEST CALL
		F	START CALL STATUS REQUEST
		G	START ORIGINATING TEST CALL
		H	START BCCH FIELD STRENGTH MEASUREMENT
		J	START RECEIVER SENSITIVITY MEASUREMENT
		K	HANDLE ABIS LOOP TEST
		L	LIST ACTIVE ABIS LOOP TESTS
		N	INTERRUPT TEST
		R	START ANTENNA TEST
		S	START TRANSCEIVER TEST
		P	PRINT TEST REPORT
		D	DELETE TEST REPORT
ZU	C	SCHEDULED RADIO NETWORK TEST HANDLING COMMANDS
		C	CREATE SCHEDULED TEST
		D	DELETE SCHEDULED TEST
		I	INTERROGATE SCHEDULED TEST
		M	MODIFY SCHEDULED TEST FUNCTIONAL PARAMETERS
		S	CHANGE SCHEDULED TEST STATE
		T	MODIFY TIME PARAMETERS OF SCHEDULED TEST
		V	HANDLE THRESHOLD PARAMETERS
ZU	D	DIAGNOSTICS HANDLING COMMANDS
		U	START UNIT TEST/PARTIAL UNIT TEST
		D	START I/O DEVICE TEST
		H	OUTPUT DIAGNOSTIC REPORT HISTORY
		I	INTERROGATE PARTIAL UNIT TESTS
		L	LIST FAULTY UNITS/PROCESSOR UNITS
		Q	INTERROGATE CURRENT TESTS
		S	STOP CURRENT TEST
ZU	S	WORKING STATE AND RESTART HANDLING COMMANDS
		C	CHANGE UNIT STATE
		T	CHANGE UNIT INFO
		W	WARM UP SPARE UNIT
		I	INTERROGATE UNIT STATE
		L	LIST UNITS IN SPECIFIED STATE OR INFO
		U	RESTART UNIT
		S	RESTART SYSTEM
ZW	SYSTEM CONFIGURATION ADMINISTRATION
ZW	A	WIRED ALARM CONNECTIONS HANDLING COMMANDS
		O	OPEN ALARM CONNECTION
		C	CLOSE ALARM CONNECTION
		I	OPEN ALARM INPUT
		D	CLOSE ALARM INPUT
		X	MODIFY ALARM INPUT PARAMETERS
		P	PRINT OPEN CONNECTIONS/INPUTS
		A	CREATE EXTERNAL ALARM
		M	MODIFY EXTERNAL ALARM PARAMETERS
		R	REMOVE EXTERNAL ALARM
		T	PRINT EXTERNAL ALARMS
		E	TEST CARTRIDGE ALARMS
ZW	B	COMPUTER CONFIGURATION HANDLING COMMANDS
		A	ADD MESSAGE BUS ADDRESS
		M	MODIFY MESSAGE BUS ADDRESS
		R	REMOVE MESSAGE BUS ADDRESS
		E	DELIVER DATA TO ALL COMPUTERS
		I	INTERROGATE COMPUTER CONFIGURATION
ZW	G	TRANSCODER CONFIGURATION COMMANDS
		C	CREATE TRANSCODER PCM
		D	DELETE TRANSCODER PCM
		M	MODIFY TRANSCODER PCM
		O	OUTPUT TRANSCODER PCM INFORMATION
		S	SET NUMBER OF THROUGH CONNECTED CHANNELS
		A	ADD THROUGH CONNECTED CHANNEL
		R	REMOVE THROUGH CONNECTED CHANNEL
		F	FETCH THROUGH CONNECTIONS FROM TRANSCODER
		I	INTERROGATE ROUTINE TEST INFORMATION
		T	MODIFY ROUTINE TEST DATA AND PARAMETERS
ZW	I	INTERNAL PCM CIRCUITS CONFIGURATION COMMANDS
		P	INTERROGATE PCM CIRCUITS OF IDENTIFIED SWITCH
		L	INTERROGATE PCM CIRCUITS OF IDENTIFIED COMPUTER OR PROGRAM BLOCK
ZW	K	SOFTWARE PACKAGE FALLBACK HANDLING COMMANDS
		S	START FALLBACK COPYING
		Q	QUIT FALLBACK COPYING
		I	INTERROGATE FALLBACK COPYING
		P	DISPLAY FALLBACK LOGFILE
ZW	N	CHANGE DELIVERY HANDLING COMMANDS
		A	ADD CHANGE DELIVERY
		D	DELETE CHANGE DELIVERY
		H	LIST CHANGE DELIVERY HISTORY
		I	INTERROGATE CHANGE DELIVERY
		J	UPDATE PACKAGE IDENTIFIER
ZW	O	PARAMETER HANDLING COMMANDS
		C	CHANGE PARAMETER VALUE
		I	INTERROGATE PARAMETER VALUE
		A	ACTIVATE/DEACTIVATE OPTIONAL FEATURE
		S	OUTPUT FEATURES ACTIVATION STATUS
ZW	Q	SOFTWARE PACKAGE ADMINISTRATION COMMANDS
		B	VERIFY SOFTWARE PACKAGE
		C	CREATE SOFTWARE PACKAGE
		D	DELETE SOFTWARE PACKAGE
		H	LIST SOFTWARE PACKAGE CHANGE HISTORY
		L	LIST SOFTWARE PACKAGE CONTENTS
		M	COMPARE SOFTWARE PACKAGES
		O	SHOW SOFTWARE PACKAGE INFORMATION
		V	INTERROGATE MODULE VERSION LOADED IN UNIT
ZW	R	SOFTWARE PACKAGE DEPLOYMENT HANDLING COMMANDS
		A	ADD UNITS TO TRIAL CONFIGURATION
		R	REMOVE UNIT FROM TRIAL CONFIGURATION
		D	DESTROY TRIAL CONFIGURATION
		S	CUTOVER TO NEW SOFTWARE PACKAGE
		O	RETURN TO OLD SOFTWARE PACKAGE
		C	COMPLETE NEW CONFIGURATION
ZW	S	SOFTWARE PACKAGE STATUS HANDLING COMMANDS
		D	SELECT DEFAULT SOFTWARE PACKAGE
		C	CHANGE STATUS OF TWO SOFTWARE PACKAGES
		S	SWITCH ACTIVE PACKAGE IN DIRECTORY
		A	ALLOW AUTOMATIC RETURN TO SPARE PACKAGE
		B	DENY AUTOMATIC RETURN TO SPARE PACKAGE
		R	ROLLBACK STATUSES OF CREATED PACKAGES
		I	INTERROGATE AUTOMATIC RETURN SETTINGS
ZW	T	EQUIPMENT MANAGEMENT COMMANDS
		J	CREATE RACK OR CABINET
		K	DELETE RACK OR CABINET
		C	CREATE CARTRIDGE
		D	DELETE CARTRIDGE
		U	CREATE UNIT
		V	DELETE UNIT
		P	CREATE PLUG-IN UNIT
		Q	DELETE PLUG-IN UNIT
		F	CREATE FUNCTION
		G	DELETE FUNCTION
		I	INTERROGATE INFORMATION
		L	LIST EQUIPMENT IN CSV-FORMAT
ZW	U	UNIT CONNECTIONS HANDLING COMMANDS
		C	CONNECT FUNCTIONAL UNIT
		D	DISCONNECT FUNCTIONAL UNIT
ZW	X	SOFTWARE CONFIGURATION RESOURCE HANDLING COMMANDS
		E	RESERVE OPERATION RESOURCES
		I	RELEASE RESOURCE RESERVATION
		F	INTERROGATE RESOURCES
		P	DISPLAY OPERATION EXECUTION CONDITION
ZY	SYSTEM SUPERVISION
ZY	E	EXCHANGE TERMINAL SUPERVISION HANDLING COMMANDS
		M	MODIFY ET PARAMETERS
		O	OUTPUT ET PARAMETERS
		A	MODIFY ALARM LIMITS
		P	OUTPUT ALARM LIMITS
		S	MODIFY STATISTICS COUNTERS LIMITS
		L	OUTPUT STATISTICS COUNTERS LIMITS
		U	MODIFY SLIP LIMITS
		R	OUTPUT SLIP LIMITS
		G	MODIFY T1 FUNCTIONAL MODES
		H	OUTPUT T1 FUNCTIONAL MODES
		F	INTERROGATE PCM SERVICE STATE
ZY	I	V3 INTERFACE LOOPBACK HANDLING COMMANDS
		C	CREATE LOOPBACK(S)
		R	REMOVE LOOPBACK(S)
		I	INTERROGATE LOOPBACK(S)
ZY	M	PCM STATISTICS:  MEASUREMENT AND OUTPUT COMMANDS
		C	CANCEL TEMPORARY MEASUREMENT
		O	OUTPUT STATISTICAL DISTURBANCES ON ONE CIRCUIT
		P	OUTPUT MEASUREMENT PERIOD PARAMETERS
		S	START TEMPORARY MEASUREMENT

Best of luck in your Telecom journey!